Advices

THE ROOM
Each room possesses a natural tendency to soften some frequencies and to amplify others. These phenomena of "resonance" vary according to the geometrical characteristics of the room and the presence of various objects (each obstacle located near the listener can be a source of "reflections" harmful to the quality of stereo sound). Therefore, to obtain the best possible results you should try to stay as close as possible to the following configuration:

- Use a large room (the greater the dimensions are, the better low frequencies are restored).
- Use an absorbent coating on the walls and curtains on the windows.
- Try not to have both a reflecting floor and a reflecting ceiling (for instance, use a carpet or an absorbent ceiling coating).
- The wall located behind the speakers should be reflective to amplify the image.
- Lateral walls should be symmetrical, to avoid a distortion of the stereophonic image.
- Finally, the wall situated behind the listener should be absorbent to avoid a limitation of the resonant space.

RUN IN
Mechanical parts of the speakers will need a run in to reach their nominal characteristics. This will take between 20 and 100 hours depending on sound level. The change will mostly concern the bass and low midrange. After this period, you may have to readjust the positioning of your speakers.

PLACEMENT OF THE SPEAKERS
It is necessary to carefully plan the position of your speakers in your room. The stereophonic principle implies that the listener is situated atop an equilateral triangle whose basis is defined by the two speakers. To keep a high precision of the stereophonic image, you should put your speakers as far as possible from the lateral walls, especially if those are reflecting (windows, smooth walls, etc.). The minimal distance should be approximately 50 cm (20”).

The balance between bass, midrange and treble is strongly dependent on the distance separating the speakers from walls, especially for low frequencies (bass). Thus, a woofer located near the ground will see its acoustic level double. A similar effect will happen with lateral or rear walls.
Of course the limits between these configurations are not always easy to establish. You will be able to optimize the adjustment of your speakers after having carefully listened to your sound system. A sound lacking life is usually due to absorption of high frequencies. You will be able to increase their level by putting the strap on a higher position. If the sound is too incisive, it is probably caused by an excess of "reflections" from high frequencies, you will be able to decrease their level by putting the strap on a lower position.

Remarks concerning use with an audio video system:
Today, in movie theatres, the rooms are generally very absorbent and speakers are often located behind the screen. This creates an attenuation of high frequencies. To limit this effect today’s movies have a specific soundtrack recorded with a high level of treble. The conditions for a home theatre system are quite different and the sound on some video recordings can be felt as too aggressive in your room. You will be able to remedy to this by decreasing the treble level with an adjustment of the strap on the back plate of your front and central speakers.

CABLES
To improve the quality of your Hi-fi system, it is necessary to use high quality cables. To insure a sufficient transmission of energy between the amplifier and the speakers, the section of the cable should be at least 2.5 mm² (1”²).


SPIKES
The spikes are used to improve the clarity of low frequencies. For the best possible result, you should use 3 spikes per speaker, 2 in front, 1 in the back. For a smaller speaker you could use 4 spikes to ensure a better stability.


PLUG IN
Regarding the kind of speakers, they are equipped with a specific terminal, some of them allow you to use mono or bi-wiring and mono or bi-amplification. Mono wiring consists in linking your speaker to the amplifier with one set of cables while bi-wiring uses 2. To improve the quality of the link between the speaker and the amplifier this solution uses one set of cables for the boomer and another one for the tweeter and midrange. Bi-amplification consists in using one amplifier to power the boomer and a second amplifier for the tweeter and midrange. This solution optimizes amplification and will improve the precision of the speakers.


Mono-wiring terminal
There is only one terminal. Link the red terminal «1» to the red output (+) of your amplifier. Link the black terminal «2» to the black output (-) of your amplifier.